Streamyx Broadband Streamyx Broadband
www.ez-broadband.com www.ez-broadband.com

Menu

Streamyx - Installation

Riger ADSL MODEM - Smart Config

SmartConfig Installation Guide for DB102 Modem

  1. Make sure your PC Ethernet setting is set to “Obtain an IP address automatically,
  2. Reset the configuration of the modem to factory default settings by pressing the reset button for 5 seconds.
  3. Configure DB102 via the WebConfig via IP address 192.168.1.1 using login name and password as follows:
    Username:tmadmin
    Password : tmadmin
  4. Click "Home" and select "SmartConfig" from the side menu.
  5. DB102 Modem can be configured to 3 modes of operation; Bridge, PPPOE and PPPOA

Bridge Mode Configuration:

  1. Set the Operation Mode to "Bridge Mode" and click "Submit"
  2. To confirm your configuration, click the "Submit" button.
  3. Please wait while it redirects you back to the Configuration Wizard page.
  4. Next, is to set PPPOE dialer on your computer.
    For Windows 98:
    • ATTENTION: If you are running Windows 98 Second Edition (not the original Windows 98 release, nor Windows ME), you need to download and install a fix from Microsoft to prevent your machine from hanging or even completely freezing while using this protocol. Go to this link to obtain the fix:
    http://support.microsoft.com/default.aspx?scid=kb;[LN];q243199
    Installation Steps
    1. Go to folder "Dialer" in the DB102 Installation CD. Double Click on file "PPPOE098.exe" or click here to install the dialer. Click "Yes" on the RASPPPOE Installation Window.
    2. When it is successfully installed, click "Ok" to close the RASPPOE Intallation Complete window.
    3. Fill in your Streamyx's username and password provided, and click the Dial button to connect.
      If all the login information you've entered is correct, you will be logged in and then be connected to Streamyx.

For Windows XP:

  1. Open Control Panel and click on the "Network and Internet Connections"
  2. Next, click on "Network Connection" located at the bottom-right of the window
  3. Click on "Create a new connection" under the "Network Tasks"
  4. A "New Connection Wizard" dialog box will be shown.

    Click "Next" to proceed.
  5. A new dialog box will be shown for the user to specify the type of connection.

    Select "Connect to the Internet" option and click "Next" to continue
  6. Specify how do you want to connect to the Internet

    Select "Setup my connection manually" option and click "Next" to continue

    Select "Connect using a broadband connection that requires a user name and password"
  7. Specify a name for the new connection. You can put any name to identify the connection.

    Click "Next" to continue
  8. Next, input your username and password given by TMNet in the appropriate box

    You can also check the two checkboxes if you wish to enable other person to use the connection and make the connection as the default connection. Click "Next" to continue.
  9. Finally, if you would like a short cut to be placed on the desktop, check the "Add a shortcut to this connection to my desktop" checkbox.

    Click "Finish" to complete the settings.
  10. To use this connection, simply double click the shortcut on the desktop and click "Connect"

    If all the login information you've entered is correct, you will be logged in and then be connected to Streamyx.

Dynamic IP Router (PPPOE) Mode Configuration:

  1. Set the Operation Mode to "PPPOE Mode".
  2. Key in your username and password. Click on "Submit”.
  3. To confirm your configuration, click the "Submit" button.
  4. Please wait while it redirects you back to the Configuration Wizard page.
    Congratulation, your modem is now has been configured as Dynamic Router (PPPoE).

Static IP Router (PPPOA) Mode Configuration:

  1. Set the Operation Mode to "PPPOA Mode".
  2. Key in your username, password and also the IP number provided by your ISP. Click on "Submit”.
  3. Please read carefully to the instruction given. To confirm your configuration, click the "Submit" button.

    At this point, you will lose connection to the modem – Do Not Panic! and Do Not Close your browser. Please proceed with the next step.
  4. On your PC, change the IP address to the Host IP address given by your ISP.

    Change the netmask according to the netmask given by your ISP. Change the gateway address to the modem’s IP address. Change the DNS to DNS address given by your ISP. To go back to the Web Configuration GUI, you need to change the browser's address to the new modem's IP address – you may need to re-login.< br /> Congratulation, your modem is now has been configured as Static IP Router (PPPoA).
Custom Search